Procurar Comutador De Matriz HDMI, Comutador De Matriz HDMI Sem Costura, Comutador De Matriz Coaxial no diretório Industry Directory, fabricante / fornecedor / Fábrica confiável a partir de China

Página inicial > Lista de Produto > Comutador de matriz HDMI > 4X4 HDMI Matrix with Simultaneous Cat and HDMI Outputs

4X4 HDMI Matrix with Simultaneous Cat and HDMI Outputs

Informação básica

Modelo:  YLMX0404-BL

Descrição do produto

Model NO.: YLMX0404-BL Home Audio & Theater Watts Per Channel: 451 - 550W Speaker System Audio Output Mode: Stereo Control: Wired FM: With FM Video Bandwidth: 165 MHz Input Ports: 4×HDMI, 4×IR Extender, 1×RS-232 Power Supply: 12 V/2.5 a DC (Us/EU Standards Weight: 1820 Specification: CE RoHS Home Audio & Theater Speaker Mount: Wall Mount Player Type: HDMI Splitter Finish: Aluminium Sound Channel: 5.1 HDMI Quantity: ≥7 Support Video Resolution: 480I, 576I, 480p, 576p, 720p, 1080I Output Ports: 4×cat, 4×IR Extender, 4×HDMI Dimensions: 440 mm (W)×200 mm (D)×45 mm (H) Trademark: Mealink Origin: China
HDM-944S50
4x4 HDMI Matrix with Simultaneous CAT and HDMI Outputs
Operation Manual
1.Introduction
The 4x4 HDMI Matrix with simultaneous CAT and HDMI outputs connects four HDMI sources to eight displays. This matrix features four HDMI outputs and each HDMI output is mirrored to provide a CAT-Cable output which runs simultaneously. Connect a HDV-E50IR Receiver to each of the CAT-Cable outputs to extend the HDMI signal up to 164ft/50m for multi-room connectivity. It works with Blu-Ray players, Set-Top boxes, Home Theater PCs, and game consoles that connect to an HDMI display. Any source is accessible at all times by any display by selecting it via the supplied IR Remote Control, RS-232, TCP/IP or by using the selection buttons on the front panel. This device supports High Definition Audio, and 3D signal compatibility.
2.Features
  HDMI1.3, HDCP 1.1 and DVI1.0 compliant
  Supports HDMI 3D pass-through
  Supports resolutions from VGA~WUXGA and HD resolutions from 480i~1080p dependent upon the EDID settings
  Supports transmission distances up to 164ft/50m through CAT5e/6/7 cable
  Supports simultaneous HDMI and CAT outputs
  Supports wideband IR(20-60Khz) matrix system, IR transport channel can be forward or backward
  Supports RS-232, remote control, on-panel control and TCP/IP Control
  Supports smart EDID management
  Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio transmission

3.Package Contents
4x4 HDMI over CAT Matrix:1pcs
HDMI CAT Receiver:4pcs
12V/3A DC power adaptor:1pcs
5V/1A DC power adaptor:4pcs
Operation Manual:1pcs
Wideband IR Tx calbe :4pcs
Wideband IR Rx cable :4pcs
HDMI Matrix IR extend calbe :1pcs
HDMI Matrix IR Remote:1pcs
Mounting ears:2pcs
RS232 cable:1pcs
4.Specifications
Video Bandwidth:165 MHz
Support Video Resolution:480i,576i,480p,576p,720p,1080i,
1080p24/30/50/60.
Input Ports :4×HDMI, 4×IR Extender, 1×RS-232,
1xRJ-45(Control),1xMatrix IR Extender
Output Ports: 4×CAT, 4×IR Extender, 4×HDMI
ESD Protection :Human-body Model:
± 8kV (Air-gap discharge)
± 4kV (Contact discharge)
Power Supply                12 V/2.5 A DC (US/EU standards,
CE/FCC/UL certified)
Dimensions :440 mm (W)×200 mm (D)×45 mm (H)
Weight :1820 g
Chassis Material:Metal
Silkscreen Color: Black
Operating Temperature:0 ºC~40 ºC/32 ºF~104 ºF
Storage Temperature :20 ºC~60 ºC/4 ºF~140 ºF
Relative Humidity :20~90 % RH (non-condensing)
Power Consumption :23 W(max)/0.5w(Standby)
5. PANEL FUNCTIONS
5.1 Front Panel
Part 1. LCM: Displays the information of each input and output setting and EDID                management .
Part  2.  IR:   IR Receiver window (accepts the remote control signal of this device only).
         POWER: Press this button to power the device on/off. The LED will illuminate green when the power is on, red when it is in 'Standby' mode.
         LOCK:  Press this button to lock all the buttons on the panel, press again to unlock.
Part 3. OUTPUT/INPUT: Press the OUTPUT and INPUT button to select the output corresponding input.
       For example: Press OUPUT ALL>INPUT 1, The OUTPUT A,B,C,D will be set to INPUT 1.
                  Press PTP button, The OUTPUT A,B,C,D will corresponding INPUT 1,2,3,4.
Part 4. EDID: Smart EDID management,the LCM will display the EDID operation.
              Press the MENU button will enter the EDID management window, press UP or DOWN button to select the needed EDID settting, press ENTER button to select the download input source.it can easy download any EDID mode to any input source.
         Note: The EDID mode table    
EDID Mode EDID Description
1 1080i, 2CH AUDIO
2 1080i, DOLBY/DTS 5.1
3 1080i, HD AUDIO
4 1080p, 2CH AUDIO
5 1080p, DOLBY/DTS 5.1
6 1080p, HD AUDIO
7 3D,1080p, 2CH AUDIO
8 3D, 1080p,DOLBY/DTS 5.1
9 3D,1080p, HD AUDIO
10 4k*2k, 2CH AUDIO
11 4k*2k, DOLBY/DTS 5.1
12 4k*2k, HD AUDIO
13 DVI 1024x768
14 DVI 1920X1080
15 DVI 1920X1200
16 Copy from HDMI OUTPUT1
17 Copy from HDMI OUTPUT2
18 Copy from HDMI OUTPUT3
19 Copy from HDMI OUTPUT4
EDID. What is it and what is it used for?
Under normal circumstances, a source device (digital and analog) will require information about a connected device/display to assess what resolutions and features are available. The source can then cater its output to send only resolutions and features that are compatible with the attached device/display. This information is called EDID (Extended Display Information Data)
and a source device can only accept and read one EDID from a connected device/display. Likewise, the source an only output one resolution for use by a connected device/display.
Why is EDID so important with the HDMI Matrix ?
The Matrix is complex piece of technology that replicates and switches between multiple inputs and outputs. Each connected source device will require one EDID to read. EDID management is carefully handled by HDMI Matrix to provide a single EDID for each source to read.
What options do I have to manage the EDID in the HDMI Matrix ?
First, it is important to note that each source device can only output one video/audio signal type. This includes resolutions and timings. When multiple devices/displays are used, such as with the HDMI Matrix, it is important to use devices/displays that have similar or compatible resolutions/features. This will ensure that the single video/audio signal produced by the source device is accepted by all of the connected output devices/displays.The user has the option, through the EDID management window, to choose how the unit will manage the EDID from multiple HDMI devices/displays. Therefore the user has some control over the resolutions/features that the source devices will output. The HDMI Matrix for has a multiple EDID management modes that will control how the EDID information from multiple devices/displays are combined, ignored, and routed.
5.2 Rear Panel
Part 1: PC CONTROL
  TCP/IP: This port is the link for TCP/IP controls, connect to an active Ethernet link with an RJ45 terminated cable.
  RS232: Connect to a PC or control system with D-Sub 9-pin cable for the transmission of RS-232 commands.
Part2: IR Channel
  IR EXT: if the panel sensor is obstructed or the unit is installed in a closed area out of infrared line of sight,the IR RX receiver included can be inserted into the IR EXT port at the rear to extend the IR sensor range and enable local control of the matrix.
  IR IN/OUT: Super IR control system interface. for further details, please refer to the Super IR system control introduction.
Part3: HDMI INPUT
   Connect to the HDMI input source devices such as a DVD player or a Set-top Box with HDMI cable.
Part4: HDMI and CAT OUTPUT
   The HDMI OUTPUT connect to HDMI equipped TVs or monitors and the CAT OUTPUT connect to the CAT Receiver.
Part5: DC POWER IN
Plug the 12V/2.5A DC power supply into the unit and connect the adaptor to an AC outlet.
6. Remote Control
  1. Press this button to power on the matrix or set it to
standby mode.
2.Press these button to select output A,B,C,D for input 1,2,3,4 port.
7. Super IR Control system(IR Call-back of Matrix and Source Devices)
The matrix is not only a switcher and extender of multiple HDMI signals to multiple HDMI receivers located remotely, it also passes IR control signals through the IR call-back system to the matrix and HDMI sources for full, independent control of all connected inputs from output locations.
Two-way IR Call-back Between matrix, Sources and Displays from Multiple Locations
A key feature on the matrix is discrete IR control of the matrix, sources and displays from any location - so inputs at the matrix end can be controlled at a display location and displays can be controlled at the matrix location. This is accomplished by placing a series of IR Emitters on devices to control and IR Receivers at all locations you wish to control from to enable the IR signal to travel both ways via the single Cat5e/6/7 cable.
01. At Matrix end: Insert the 3.5mm jacks of the IR TX Emitters included with the unit into the IR TX Emitter ports at the rear of the matrix according to input. The IR signal is added to the HDMI of the input device so, for example, if the user is watching Blu-ray on input 1, the IR signal will be directed through the IR TX1 socket to control the device.
As each IR TX port is allocated to an individual HDMI input port, if the user is unable to establish IR control of the device, care should be taken to check firstly, that the IR emitter and HDMI input ports match (Input 1-TX1, Input2-TX2 etc.) with plugs secured in correct ports, and secondly, that the IR TX emitter sensors are firmly attached directly to the front of inputs and covering infrared sensor windows of the source devices.Some later adjustment may be needed to the location of the sensor to achieve the best performance results - sometimes moving the sensor to different areas on the source can improve IR performance.
NOTE: Infrared receiving areas of devices can be located by shining a flashlight onto the front of the device - the sensor should be able to be seen through the plastic as a small, round object inside.Insert 3.5mm jacks of IR RX receivers into RX ports, making sure the receivers themselves are placed in clear view to receive an infrared signal from the remote handset used to control the display outputs.
02. At display end: Insert the IR RX Receiver jack into the IR RX port of the display receiver balun, with the receivers themselves placed in clear view on or near the displays to receive an infrared signal from the remote handset used to control inputs.Insert the IR TX Emitter jack into the IR TX port of the display receiver balun, ensuring that the emitter sensor is securely attached to infrared sensor window of the display.Follow the same connection and positioning for all baluns/displays connected to the matrix.If all IR TX Emitters and IR RX Receivers are positioned and connected correctly with sources, displays and display receivers fully powered and the matrix set to IR call-back enabled and IR TX Swicth mode activated, two-way IR will now be possible.
Note: Misplaced or poorly secured IR Emitters and Receivers may result in intermittent IR control signals passed to and from the matrix. Check your placement and adjust if necessary.
ADVANCED OPERATION
Typically, unless alternative methods of controlling the matrix are chosen or problems with device communication through the matrix encountered, basic operation is all that is required to operate your matrix. However, the following information on advanced operation will detail how the matrix system can be configured and for advanced control and settings can be altered or data manually input should such problems arise, as well as configuring the system for third party control.
8. HDMI CAT Receiver
1.HDMI OUT: This slot is where you connect the HDTV or monitor with HDMI cable for input source display.
2.POWER LED: This blue LED illuminate when the device is connected with power supply.
3.LOCK LED: This blue LED illuminate when the signal locked.
4.Coaxial OUT: This slot is where you connect to the amplifier with coaxial cable.
5.ARC SW: Switch this sw to open or close the ARC fuction.
6.DC 5V: Plug the 5V DC power supply into the unit and connect the adaptor to AC wall outlet.
7.IR RX: This 3.5mm phone for super IR control system IR receiver .
8.IR TX: This 3.5mm phone for super IR control system IR Emitter.
9.CAT5E/6: This CAT5E/6 port connect to HDMI Matrix CAT OUTPUT with CAT5e/6/7 cable.
9. PC controller user guide
Installation
Matrix controller is a green software. Just copy MatrixController.exe to PC which is used to control the Matrix by RS232 COM port or TCP/IP to complete installation.
Preparation
Connect PC and Matrix by RS232 cable (headers of both sides of cable should be FEMALE) or TCP/IP(local area network)
Power-up Matrix
Double click MatirxController.exe icon to run it
How to control Matrix
"General" page
Select RS232 COM or TCP mode
Select RS232 COM port
Click to connect or disconnect PC and Matrix
Select Matrix IP
Connet to Matrix IP
Search Matrix IP
Configure Matrix IP and MAC
Enable or disable IR /beep
Device information display area
Click to refresh device status: include device information displayed in
area and Input/Output Settings on "Matrix" page
Configure TCP
After action of  , edit form will pop-up as below:
Select auto or static IP
Rewrite the Matrix IP
Rewrite the Matrix MAC
"EDID control" page
Set EDID mode for selected Input port or All Input ports, click "Set" button to complete action
Select EDID
Select Input port
Copy EDID from Output port to selected Input port or All Input ports, click "Set" button to complete action.
Select Output port
Download EDID content to selected Input port or All Input ports, click
"Download" button to complete action.
Open EDID binary file
Display EDID binary file path
LED which display Input number for respective Output
Click to select Input port for respective Output port
Click to select previous or next Input port for respective Output port
"FW upgrade" page

Click to open FW file(file extension is ".fw")
Display the FW file path
Displaying the progress of the software upgrade
Click to upgrade the Matrix software
Display the message of the software upgrade
Clear the message of the software upgrade
10. Operate and Connect
1.  Connect up to 4 sources such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI inputs on the unit. Do not hotplug! Insert and extract cables carefully with the power SWITCHED OFF. Connecting and disconnecting while the unit is powered can result in damage to circuitry.
2.  Connect the output UTP ports and/or HDMI output ports, starting with output 1, to the E50IR Receiver display receivers (sold separately) (using well terminated or pre-terminated Cat5e/6 cables no longer than 160 ft)
3.  If utilizing UTP, connect the output HDMI ports of the E50IR Receiver display receivers (sold separately) to high-definition displays such as an HDTV or HD projector that use HDMI inputs. Note that high-speed HDMI cables are recommended for the distances that are required for each connection.
4.  Plug in IR transmitters to the back of the Matrix Selector Switcher unit (IR TX), the transmitters are labeled IR TX, place in front of the IR receiver of the source, ensure that each emitter is placed in front of the IR receiver eye. Double-sided adhesive tape provided.
5.  Plug in IR receivers to the port of the E50IR Receiver display receivers (sold separately) ,the receivers are labeled IR RX, use provided double-sided adhesive tape to stick emitters at each display at a desired place that will receive a remote signal.
6.  For power, plug in the source first, followed by the Matrix Selector Switcher (power supply included), followed by the display receivers, followed by each output connected.
7.  Power on each device in the same sequence.
At this point each display connected should display the assigned source (input 1 at default when powered on initially), scroll through each of the sources on each display to ensure everything is in working order. Use included IR remote at each display receiver to test switching function between sources and IR function itself. If a display is having difficulty receiving a signal, access the display's menu and adjust the resolution (lowest to highest until signal is displayed). A 24 Hz vertical refresh rate may work better than 60 Hz or higher. If the IR remote function is not responding, check the emitters to ensure they are placed correctly and are plugged into the correct IR jacks on the Matrix Selector Switcher unit.
 

Grupo de Produto : Comutador de matriz HDMI

Enviar e-mail para este fornecedor
  • *Assunto:
  • a:

  • *Mensagens:
    Sua mensagem deve estar entre 20-8000 caracteres